camshaft

The camshaft rotates in phase with the crankshaft, but at half its speed.

凸轮轴和曲轴协调旋转, 但速度仅是曲轴的一半.

This is called an overhead camshaft arrangement.

这被叫为顶置凸轮轴装置.

The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.

那金属轴叫凸轮轴, 在发动机里的每个气门一般有各自的凸轮.

As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.

当凸轮轴旋转时, 凸轮凸起的或者高点的位置, 推动气门座.

The influence of inoculant addition amount on the structure and properties of camshaft was investigated.

试验了孕育剂量对凸轮轴组织和性能的影响.

The front timing cover and and a finished camshaft with timing gear on the end.

前面的时间和范围,并完成与凸轮轴齿轮的时间就结束.

The isothermal quenching process of the ductile iron camshaft was analyzed.

对球铁凸轮轴的等温淬火工艺进行了分析.

The manganate phosphating technology of camshaft is introduced.

介绍凸轮轴的磷化工艺.

A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.

推导出了保持磨除率基本恒定时,数控凸轮轴磨床磨削凸轮时凸轮轴转速变化的计算公式.

Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.

两个上死点的传感器安装在凸轮轴的后面.

The camshaft and crankshaft gears can be connected directly, or meshed.

凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.

The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.

曲轴的转速与凸轮轴的转速之比是2∶1.

The camshaft has a cam, on which there is a lob , or bump.

凸轮轴上有一个凸轮, 凸轮上有一个凸角.

A camshaft driven by a chain or belt turns in the same direction as the crankshaft.

凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.

In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.

详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.

Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.

顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.

Argon arc remelting hardening is a new technology of manufacturing camshaft.

氩弧重熔硬化是生产凸轮轴新工艺.

This means that the crankshaft will make two revolutions for every revolution of the camshaft.

这意味着凸轮轴每旋转一次曲轴将旋转两次.

Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.

拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.

Since 1958, an engine with a single overhead camshaft has been used.

从1958年起, 便已使用带有单顶置凸轮机的发动机.

These engines are known as dual overhead camshaft ( DOHC ) engines.

这些发动机被称为双顶置凸轮轴 ( DOHC ) 发动机.

The opening of each valve is controlled by a camshaft.

每个阀门的开启由凸轮轴控制.

Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.

工件恒角速度磨削和工件恒线速度磨削是目前精加工凸轮轴的主要磨削加工工艺.